Key Benefits
- Compatible with Newton CP pumps, NP pumps and NP eco pumps
- Adjustable neck ensures that the lid is always at the correct height, regardless of floor finishes
- Supplied with sealed and locked recess lid. High-end finish lids and frames are available as cost options
- Flat areas to side of chamber, ready for wall flanges to receive incoming 110 mm drainage pipes. Wall flanges are available as cost options
- Large foot to base of chamber to prevent flotation
- Anti-Drip system available for the inside of the chamber
- Sump is always set into the slab at the same height, meaning connections in from Newton Basedrain System and connections out of the chamber are at the same height with every installation
Typical Applications
- The Titan-Pro is specifically designed to be used with the Newton CDM System, our ‘Type C’ cavity drain waterproofing system
- Basements and cellars
- Light-wells
- Surface water pumping receiving water from gullies and surface slot drainage
BS 8102:2009 the British Standard for Waterproofing
The British Standard 8102:2009 Code of Practice for Protection of Below Ground Structures Against Water From the Ground is the main design guide for structural waterproofing in the UK.
Newton System 500 is a maintainable system, so complies with BS 8102 requirements. BS 8102 also specifies that “a waterproofing specialist should be included as part of the design team so that an integrated waterproofing is created”.
Therefore it is our recommendation that the Newton CDM System is installed by a Newton Specialist Basement Contractor (NSBC).
Pump Configurations & Product Codes
The Titan-Pro chamber can be purchased as a bare sump or as a fully built pumping system. As a bare pump, it can be supplied with or without lid and frame and either pre-drilled and un-drilled.
Sump Chambers
If you only need a chamber or want to order your pumps separately, choose from our drilled and undrilled Titan-Pro chambers, both with and without lids.
Code |
Drilled |
Lid |
Description |
TPC |
No |
No |
Titan-Pro Sump Chamber only |
TPCD |
Yes |
No |
Titan-Pro Sump Chamber – Drilled |
TPC&L |
No |
Yes |
Titan-Pro Sump Chamber with Lid |
TPCD&L |
Yes |
Yes |
Titan-Pro Sump Chamber with Lid & Drilled |
Sump Chambers & Pumps
A Newton PA50 High Water Level Alarm is included with automatic pump systems.
For more information on the individual pump units that can be ordered with the Titan-Pro chamber, call our Technical Team on 0800 7022176
Built Systems – Twin pumps – 1 x Rising main |
Code |
Pump Model |
No. of Pumps |
Auto or Manual |
Rising Mains |
CDM1 |
CP250 |
2 |
Automatic |
1 |
CDM2 |
CP250 |
2 |
Manual |
1 |
CDM3 |
CP400 |
2 |
Automatic |
1 |
CDM4 |
CP400 |
2 |
Manual |
1 |
CDM5 |
NP400 |
2 |
Automatic |
1 |
CDM6 |
NP400 |
2 |
Manual |
1 |
CDM5 eco
|
NP400 eco
|
2 |
Manual |
1 |
CDM6 eco
|
NP400 eco
|
2 |
Auto |
1 |
CDM7 |
CP750 |
2 |
Automatic |
1 |
CDM8 |
CP750 |
2 |
Manual |
1 |
CDM11 eco
|
NP750 eco
|
2 |
Automatic |
1 |
CDM12 eco
|
NP750 eco
|
2 |
Manual |
1 |
Where increased pump flow (pump duty assist) is required, twin rising main systems should be considered.
Built Systems – Twin pumps – 2 x Rising main |
Code |
Pump Model |
No. of Pumps |
Auto or Manual |
Rising Mains |
CDM9 |
CP750 |
2 |
Automatic |
2 |
CDM10 |
CP750 |
2 |
Manual |
2 |
CDM13 eco
|
NP750 eco
|
2 |
Automatic |
2 |
CDM14 eco
|
NP750 eco
|
2 |
Manual |
2 |
Downloads
Warranty
Newton pumps prefixed NP are supplied by Newton Waterproofing Systems with a 3-year back-to-base warranty. This is increased to 5-years if under a servicing regime by a Newton approved servicing company/engineer.