Description
SilaCote Spray – Single-Component Liquid Waterproofing Membrane
SilaCote Spray is a single-component, moisture-triggered, silane-based liquid waterproofing membrane designed for larger roofing and waterproofing projects where spray application is preferred. Its ready-to-use formulation creates a seamless, flexible and durable membrane without joints or overlaps, providing long-term protection against water ingress.
Based on aliphatic silane technology, SilaCote Spray is solvent-free, isocyanate-free and has a stated VOC content of 0g/l. It is designed for application to suitable prepared substrates and can be used for flat roofs, balconies, terraces, walkways, concrete structures and other waterproofing applications. The membrane provides water vapour permeability, crack-bridging properties and resistance to weathering and standing water when installed as part of a suitable system.
SilaCote Spray is specifically formulated for larger coverage areas without the need for thinning. It can be applied in two or three layers, with a total material consumption dependent on the substrate, required thickness and application conditions.

Key Features & Benefits
- Designed for spray application: Suitable for covering larger waterproofing areas efficiently.
- Single-component system: Ready to use, with no separate mixing of components required.
- Moisture-triggered curing: Cures through reaction with atmospheric moisture.
- Seamless waterproofing: Forms a continuous membrane without joints or overlaps.
- Solvent-free: Formulated without added solvents.
- Isocyanate-free: Does not use isocyanate-based polyurethane chemistry.
- Low VOC formulation: Manufacturer-stated VOC content of 0g/l.
- High solids content: Approximately 99% solids by volume.
- Flexible membrane: Designed to accommodate movement and bridge suitable substrate cracks.
- Water vapour permeable: Allows water vapour transmission through the membrane.
- Weather resistant: Resistant to water and frost.
- Chemical resistance: Resistant to detergents, oils, seawater and domestic chemicals, as stated by the manufacturer.
- Repairable: Localised repairs can be carried out where required.
- Cold-applied system: No hot works are required during application.
- No routine topcoat required: The aliphatic formulation is designed to provide UV stability without a separate protective topcoat in the stated applications.
Suitable Applications
SilaCote Spray is designed for waterproofing and protecting a range of suitable building and construction surfaces, including:
- Flat and low-pitched roofs
- Roof refurbishment and renovation projects
- Balconies, terraces and verandas
- Walkways and pedestrian traffic decks
- Recoating suitable existing single-ply roofing membranes
- Roof details, upstands and penetrations
- Roof outlets, drainage channels and valley gutters
- Internal wet areas and under-tile waterproofing
- Concrete structures and construction surfaces
- Bridge decks, tunnels and stadium stands
- Protection of suitable polyurethane foam insulation
- Steel, timber and suitable plastic surfaces
- Green roof and protected roof applications, subject to system compatibility
For specialist applications such as ponds, fountains, swimming pools, permanent water immersion, living walls or tank flotation compartments, obtain confirmation from the manufacturer before use. These applications should not be assumed to be covered by the general Spray technical data sheet.
Technical Information
| Product | SilaCote Spray |
| Product type | Liquid-applied waterproofing membrane |
| Technology | Single-component moisture-triggered silane-based aliphatic membrane |
| Application | Spray application for larger areas |
| Thinning | Not required for the Spray formulation |
| Colour | Off-white or mid grey |
| Specific gravity | 1.30 ± 0.05 |
| Solids by volume | 99% ± 1% |
| VOC content | 0g/l |
| Recommended application | Two or three layers |
| Consumption | Approximately 0.65–2.6kg/m² |
| Skin formation | Approximately 10 minutes at 20°C and 65% relative humidity |
| Rain stability | Approximately 15 minutes at 20°C and 65% relative humidity |
| Light pedestrian traffic | After approximately 18–24 hours |
| Final curing | Approximately 7 days |
| Shelf life | 9 months unopened |
| Storage temperature | 5°C to 40°C, stored indoors |
Coverage note: The stated consumption range is based on application by roller to a smooth surface under optimum conditions. Actual material usage will vary according to substrate porosity, surface profile, temperature and application method. For project estimates, allow for the condition of the existing substrate and the specified membrane build-up.
Coverage & Material Requirements
The manufacturer's technical data sheet gives a consumption range of approximately 0.65–2.6kg/m², applied in two or three layers.
Indicative material requirements at the stated consumption rates:
| Area | At 0.65kg/m² | At 2.6kg/m² |
| 10m² | 6.5kg | 26kg |
| 25m² | 16.25kg | 65kg |
| 50m² | 32.5kg | 130kg |
| 100m² | 65kg | 260kg |
These figures illustrate the full published consumption range, not a guaranteed coverage rate. The correct application rate must be established for the substrate and required system thickness.
Application Instructions
1. Substrate Preparation
- Ensure the substrate is sound, stable and suitable for the proposed waterproofing system.
- Remove loose material, dust, dirt, grease and contaminants that could affect adhesion.
- Repair significant defects and prepare joints, cracks, outlets, upstands and penetrations before application.
- Check compatibility with existing roof coatings and membranes before overcoating.
- Although the manufacturer promotes primer-free adhesion on many conventional substrates, suitability should be confirmed for the actual substrate and project conditions.
2. Spray Application
- SilaCote Spray is supplied ready to use and is designed for larger areas without thinning.
- Use suitable spray equipment and application settings confirmed by the manufacturer.
- Apply evenly in two or three layers in accordance with the specified membrane build-up.
- Maintain consistent coverage and pay particular attention to roof details, outlets, upstands and changes in direction.
- Ensure the required total material consumption is achieved across the waterproofing area.
- Follow the manufacturer's application guidance for any required reinforcement at joints, cracks and critical details.
3. Drying and Weather Conditions
- Skin formation is approximately 10 minutes at 20°C and 65% relative humidity.
- Rain stability is approximately 15 minutes under the same stated conditions.
- Light pedestrian traffic is possible after approximately 18–24 hours.
- Final curing takes approximately 7 days.
These times are indicative and will vary with temperature, humidity, membrane thickness and site conditions. Rain stability does not mean the membrane has fully cured or is immediately ready for ponding water or permanent immersion.
Primers & Reinforcement
Primers
The manufacturer promotes SilaCote as a primer-free system on most conventional suitable substrates. However, substrate condition and compatibility must be assessed before application. Confirm any special preparation or primer requirements with the manufacturer where the substrate is unusual or previously coated.
Reinforcement
Reinforcement mesh can be incorporated where required by the system design, particularly around cracks, joints, penetrations, outlets and other critical detailing. The need for reinforcement depends on the substrate and project conditions; it is not automatically required across every application.
Important Application Considerations
- SilaCote Spray is a specific grade intended for larger areas. Do not confuse it with SilaCote ST 100, ST 200 or ST 300, which have different application methods and equipment requirements.
- Do not thin the Spray formulation unless expressly instructed by the manufacturer.
- Use suitable spray equipment and follow the manufacturer's application guidance.
- Do not assume that every existing roof covering is suitable for direct overcoating.
- Check compatibility with the substrate and any existing coating before commencing work.
- Observe the stated storage conditions and 9-month unopened shelf life.
- Allow adequate curing before exposing the membrane to heavy traffic, standing water or service conditions.
- Confirm specialist applications such as ponds, water features and permanent immersion with the manufacturer before use.
Frequently Asked Questions
What is SilaCote Spray used for?
SilaCote Spray is a single-component liquid waterproofing membrane designed for larger roofing and construction areas. Applications include flat roofs, balconies, terraces, walkways and suitable concrete structures.
What is the difference between SilaCote Spray and SilaCote ST 300?
SilaCote Spray is designed for larger areas and spray application without thinning. SilaCote ST 300 is a different grade intended for brush or trowel application and cannot be sprayed. Always select the correct grade for the intended application equipment.
Does SilaCote Spray require mixing?
No. It is a single-component, ready-to-use product. No separate component mixing is required.
Does SilaCote Spray need a primer?
The manufacturer promotes SilaCote as a primer-free system on most conventional suitable substrates. The actual substrate must still be checked for compatibility and preparation requirements.
How much SilaCote Spray do I need?
The technical data sheet gives a consumption range of approximately 0.65–2.6kg/m² in two or three layers. Actual consumption depends on substrate condition, porosity, application method and required membrane build-up.
How quickly is SilaCote Spray rain resistant?
The technical data sheet gives a rain stability time of approximately 15 minutes at 20°C and 65% relative humidity. Actual times will vary with site conditions and application thickness.
How long does SilaCote Spray take to cure?
Light pedestrian traffic is possible after approximately 18–24 hours, while final curing takes approximately 7 days under the stated test conditions.
Is SilaCote Spray UV stable?
The manufacturer describes the SilaCote aliphatic formulation as UV stable. It is designed for external waterproofing applications, subject to the specified system build-up.
Can SilaCote Spray be used on ponds and water features?
The wider SilaCote product literature lists ponds, fountains and water features as possible applications. However, the Spray technical data sheet does not provide sufficient detail to confirm suitability for every fish pond or permanent immersion application. Obtain manufacturer confirmation before use.
What colours are available?
The Spray technical data sheet lists off-white and mid grey. Check the available product variants before ordering.
Technical Downloads
Download the manufacturer's technical data sheet for product specifications, application guidance, consumption and drying information.
Safety Data Sheet: Please contact Clever Shield or the manufacturer for the current SilaCote Spray SDS before use. The existing placeholder link on this product page does not provide the actual safety document.
Buy SilaCote Spray Waterproofing Membrane
Clever Shield Coatings UK supplies SilaCote liquid waterproofing products for roofing, refurbishment and construction applications throughout the UK.
For product availability, project quantities and technical document enquiries, contact our team on 01268 472358.
Clever Shield supplies products but does not design or specify waterproofing systems. Customers must confirm product suitability, substrate compatibility and system requirements and follow the latest manufacturer technical data sheets, safety information and installation instructions.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Security

You may also be interested in
Recently viewed
What Our Customers Say
Very good 4.7/5
Exceptional Advice & Support
Hands down in all of my reviews I've done in 21+ years, Clever Shield Coatings is one I'll always remember as the staff are friendly & passionate about their job - looking out for the customer and getting the job done right first time.
Sunny
Verified customer
Fast, friendly and reliable…
Fast, friendly and reliable. I was able to get my job done quickly and my customer was happy with the prices.
Thanks.
Kamil
Verified customer
Exceptional Advice & Support
We have been using clever shield (dealing with Richard) for over 2 years. They always give good service deliveries on time and even give technical advise when needed.
JAC
Verified customer
Really helpful! great service
Spoke to technical for some advice on the product and it was really helpful, great service
Tina Mansfield
Verified customer
Great company / knowledgeable
What a great company - knowledge about the products, spent lots of time talking me through everything - if only every company was like this one !
Ostler Info
Verified customer
Great company and speedy delivery
Really great company to deal with,excellent customer service,speedy delivery will definitely recommend and use again as a satisfied customer
Del Upson
Verified customer
Great Technical Support
Great technical support and advice on wykamol products would highly recommend this company
Shirley
Verified customer
Highly Recommended
Sandra Dow
Verified customer






